Bambu Lab P2S – specs, what is new, setup and manual

Updated November 22, 2026

Key points
  • The P2S was announced on 14 October 2025 as a re-engineered successor to the P1S.
  • It keeps the 256 × 256 × 256 mm build volume and adds a 5-inch touchscreen, 1080p camera and quick-swap nozzle.
  • Bambu Lab lists a 300 °C nozzle, a 110 °C bed and a servo extruder with up to 8.5 kg of force.
Specifications (from the maker’s published spec sheet)
Build volume256 × 256 × 256 mm
Max nozzle temperature300 °C
Max heatbed temperature110 °C
Nozzle0.4 mm included; 0.2 / 0.6 / 0.8 mm supported; quick-swap hot end
ExtruderPMSM servo extruder, up to 8.5 kg extrusion force
Screen5-inch touchscreen
Camera1080p live view with timelapse
FiltrationActivated-carbon filter
SensorsDoor, filament run-out, tangle, odometry; power-loss recovery; filament cutter
Combo versionIncludes AMS 2 Pro with active-venting filament drying
Launch price (EU)€519 printer / €749 Combo, tax included

The Bambu Lab P2S is the second generation of Bambu Lab’s enclosed P-series. Bambu Lab announced it on 14 October 2025 and describes it as a completely re-engineered P1 that borrows technology from the larger H2D and H2S.

What is new compared with the P1S

  • Screen and interface. A 5-inch touchscreen with Bambu Lab’s second-generation interface replaces the P1S’s small button-driven screen.
  • Extruder. A PMSM servo extruder with up to 8.5 kg of force, which Bambu Lab says is 70% more than its predecessor. It checks resistance and position at 20 kHz to spot grinding and clogs.
  • Calibration. Auto Flow Dynamics Calibration uses an eddy-current sensor.
  • Cooling. Adaptive Airflow pulls cool outside air in so PLA and PETG can print with the door closed, and a heat-keeping mode for ABS and ASA.
  • Camera and AI. A 1080p live-view camera with AI detection of spaghetti failures, nozzle blobs and air printing, plus a check that the plate and nozzle match the slicer settings.
  • Maintenance. A quick-swap hot end that releases the nozzle and heatsink with one clip.
  • Bed. Up to 110 °C, versus 100 °C on the P1S.

The build volume stays at 256 × 256 × 256 mm. Bambu Lab says the P1S remains on sale and supported.

The Combo and AMS 2 Pro

The P2S Combo ships with the AMS 2 Pro, which feeds up to four spools and dries filament with active venting. Bambu Lab says this dries filament 30% faster than sealed heating.

Setup and manual

The P2S arrives mostly assembled. Follow Bambu Lab’s quick-start guide and the on-screen self-test, then bind the printer to the Bambu Handy app and send prints from Bambu Studio. The official manual, FAQ and maintenance pages are on the Bambu Lab Wiki.

Compare

Sources

Questions and answers

What is the difference between the P2S and the P1S?

The build volume is the same. The P2S adds a 5-inch touchscreen, a 1080p camera, a servo extruder with about 70% more force, Auto Flow Dynamics Calibration, adaptive airflow, AI error detection, a quick-swap nozzle and a 110 °C bed (the P1S bed reaches 100 °C).

Can I upgrade a P1S to a P2S?

No. Bambu Lab says the P2S components differ fundamentally from the P1S, so a P1S cannot be turned into a P2S by swapping parts.

What build plates fit the P2S?

Bambu Lab says the P2S supports all current Bambu Lab build plates of the 256 mm size, but older plates do not support its QR-code plate recognition.